How To Set A Victor Mole Trap

Download Article

If you have a mole problem, Victor mole traps are an effective mode to impale them. The two main kinds of Victor mole traps are the Out O'Sight and Plunger-Style mole traps. The Out O'Sight trap has a set of jaws or teeth, while the Plunger-Manner has spring-loaded spikes that shoot into the ground. If you find an active mole tunnel and prepare the trap properly, yous can go rid of the moles on your property.

i
Find mole tunnels in your lawn. Wait for mounds of dirt around your belongings, every bit this is a sign of a tunnel. Poke a hole through the mound with a stick or the end of a broom handle. If the hole is covered up 24 hours later, you can assume that information technology is an active mole tunnel.^[i]
- If you lot have multiple mounds effectually your backyard, put a hole in each of them to detect all the active tunnels.
2

Dig a hole in the top of an active tunnel. Pick a tunnel that'southward been covered by a mole, and dig a hole in the pinnacle of the tunnel with a spade. The hole should exist about 6 inches (xv cm) wide and penetrate down into the mole tunnel. Dig down into the tunnel and put the dirt to the side for later.^[2]

Advertizement
3

Experience for the tunnel with your fingers. Stick your fingers into the pigsty you lot made and feel around for the pathway to the mole tunnel surreptitious. You should feel ii holes on each stop of the hole you lot just dug.^[3]

Advertizing

one

Create a mound of clay in the center of the hole. Use some of the clay that you dug up and place it dorsum into the center of the hole until the height of the mound sits affluent with the footing. The mound should be centered in between the holes in the tunnel. The lesser pan or trigger on the lesser of your trap should residual on the meridian of this dirt mound.^[4]
2

Place the setting levers over the springs. Thread the setting levers under the top of the handles on each side of the trap. Then, fit the setting levers over the springs in the middle of the trap and slide them up.^[5]
iii

Push the levers together with the palms of your hands. You lot may have to use a good amount of forcefulness to open up the teeth of the trap. Once both levers touch each other, your trap's teeth should be fully opened.^[6]
4
Flip the safety latch over the top of the trap. The safety volition be a minor metal prune on the summit of your trap. Flip it upwards and so that it catches on the other side of the clip and holds your trap open. Information technology'southward important to go on the safety latch engaged until the trap is completely prepare. You lot can now unthread the setting levers and set them aside.^[7]
- Grip both of the levers with one hand to keep them open up while you set the safety.
v
Place the end of the setting bar on the trigger pan. The trigger pan is a metal tab on the bottom of your trap, and is what the mole volition printing on to close the trap. The setting bar is the bar on the top of the trap with a hooked end. Hook the end of the setting bar onto the edge of the trigger pan. Make sure the safety latch is however engaged so that the trap doesn't close.^[8]
- When the pan is pushed up, the setting bar will undo and the trap volition close shut.
six

Identify the trap around the clay mound in the pigsty. Position the trap so that the teeth don't block the holes in the tunnel. The teeth of the trap should be effectually the mound and fit around holes in the tunnel. In one case the mole gets to the clay mound, it will try to dig through the mound, which will appoint the trap.^[9]
vii
Release the rubber on the height of the trap. Flip the rubber over. If you set everything up correctly, the teeth of the trap should remain open and slam shut when pressure is applied to the lesser of the trigger pan.^[x]
- Keep pets and children out of the grand when the mole trap is engaged.

1

Make full the hole up with loose dirt. If the clay nether the trap is as well compact, the spikes won't be able to penetrate into the ground fast plenty to grab the mole. Break upwards the soil that you dug upwards so that it's loose earlier placing it back into the hole.
2

Press downward on an active mole tunnel with your thumb. Making a depression in the dirt will collapse the tunnel. This volition require the mole to burrow through the obstructing clay the next time it uses the tunnel, which will engage your trap.^[11]
three
Press the trap over the low. Position the trap then that the side spikes don't block the tunnel beneath. The trigger pan is the metal square on the bottom of the trap, and should be positioned direct over the depression that you created in the dirt. Press down on the trap and so that the side spikes become into the ground and the trigger pan runs flush with the ground.^[12]
- The trap latch is the metal rod attached to the superlative of the trap and should exist in the downward position.
4
Pull the plunger on the superlative of the trap up and down. Pushing the spikes in and out of the dirt will loosen the soil and make the trap more efficient. Pull up and downwardly on the plunger on the top of the trap several times until the soil is loose.^[13]
- Keep hands and feet away from the bottom of the trap or you may injure yourself.
5
Pull up on the plunger until the trap snaps into place. Once you pull the plunger enough, the trap latch should snap securely onto the trigger pan.Your trap is now prepare. The adjacent time a mole tries to burrow through the clay, the spikes will spring downwardly into the clay where the mole is.^[14]
- Go along children and pets out of the yard when the mole trap is engaged.

Add New Question

Question

Where do you set up mole traps?

Elmer Bensinger is a Pest Control Specialist with Eden Avant-garde Pest Technologies in Spokane, Washington. With over 20 years of experience, Elmer specializes in integrated pest management and products such as insecticides and rodenticides. He studied business at S Puget Sound Community College.

Pest Control Specialist

Proficient Answer

Information technology depends on the manner of trap yous're using, but they typically either get in the mole hill, on top of it, or right next to it. In either case, you lot're going to demand to effigy out where the mole actually is before you set the trap.
Question

What's the well-nigh effective mole trap?

Elmer Bensinger is a Pest Command Specialist with Eden Advanced Pest Technologies in Spokane, Washington. With over 20 years of feel, Elmer specializes in integrated pest direction and products such as insecticides and rodenticides. He studied business at South Puget Sound Community College.

Pest Control Specialist

Skilful Answer

The claw-style traps that crush the mole are the most constructive. Unfortunately, the live traps aren't nearly as constructive as those claw traps.
Question

What tin I use instead of a trap?

Elmer Bensinger is a Pest Control Specialist with Eden Advanced Pest Technologies in Spokane, Washington. With over 20 years of experience, Elmer specializes in integrated pest direction and products such as insecticides and rodenticides. He studied business concern at Due south Puget Sound Community Higher.

Pest Control Specialist

Expert Reply

At that place are machines you tin can purchase that will pump the mole's tunnel with carbon dioxide to put it down. Those are adequately effective. The mole won't feel any pain either, if that's something y'all're worried almost. It will just go to sleep and die quietly.
Question

Is there a style to increase the sensitivity of the pressure plate in the victor headset mole trap?

Hobie Dial

Community Answer

To improve sensitivity, cut a one X one-1/4-inch rectangular shim out of a i/16th-inch thick piece of difficult plastic and mucilage it within and at the stop of the one-i/4-inch-wide iron channel that has the xanthous label. The shim prevents the cocking mechanism from rotating as far past the triggering point when the trap is set.